New

Lawn & Garden

Clay Pot Hanger

  like (0) I made it (2) Email Print Design File
VIEW ALL Lawn & Garden

STEPS

7

SKILL LEVEL

Brighten your space inside or out with this attractive hanging garden. This vertical clay pot hanger is perfect for adding touch of floral décor or a convenient hanging herb garden. Best of all, this garden décor is portable, allowing you to move your greenery inside for those colder months. Special thanks to the Home Depot Palm Harbor store for sharing this awesome how-to with us. Before you start the project, download and print the template using the "Design File" button above.

by Dremel ®

201 PROJECTS

Tags

Supplies Needed For This Project

TOOL

SM20-01 Saw-Max Tool Kit

Model # SM20

TOOL

Multi-Max™ MM30

Model # MM30

ACCESSORY

SM500 Wood & Plastic Carbide Wheel

Model # SM500

ACCESSORY

MM480 Wood Flush Cut Blade

Model # MM480

ACCESSORY

60, 120 and 240 Grit Sand Paper - Wood

Model # MM70W

Tools & Accessories

Materials

  • 1

    Dremel MM14 Hook and Loop Pad

  • 1

    1" x 4" Wooden Plank

  • 1

    Rope

  • 1

    Drill

  • 1

    3/4" Spade Drill Bit

  • 1

    Pencil

  • 1

    Measuring Tape

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

We will begin by cutting wood for the body of the hanger. We created our hanger out of cedar as it typically withstands weather conditions outdoors. Measure and mark a 1" x 4" wooden plank to 46" in length. Mount the SM500 Wood & Plastic Wheel in your Saw-Max tool. With your plank clamped, turn on your tool and cut along the marked line.

STEP 2

Step 2

Trace the provided pot slot template onto the plank, flipping it to trace the template along the left and right sides as desired. We alternated the spacing of our slots, leaving at least 1' between slots located on the same side of the plank to provide room for each pot and plant. Our pots had a 5" height, 4" base diameter, 6" top diameter, and 1.5" lip height. Measure and mark a circle for a rope hole. We centered ours 1.5" below the top of the plank and gave it a 3/4" diameter. Optional: Draw top and bottom designs onto the plank. For our hanger, we brought the bottom of the design to a point by drawing lines from the bottom center of the plank to points marked 2" above the bottom of each side. Additionally, we beveled the top corners of our hanger design by measuring and connecting points 3/4" from the top and side of the plank for each corner.

STEP 3

Step 3

Using a drill and 3/4" spade bit, bore out holes at the top and bottom of each pot slot silhouette traced on the plank. Then, bore out the circle drawn for the rope hole using the same drill and bit. Tip: Clamp your plank to waste lumber when boring holes to prevent blow-out from occurring.

STEP 4

Step 4

Next, cut along the two traced lines that connect each oval pot slot to its respective side of the plank. This can be done using the Dremel Saw-Max tool equipped with the same SM500 wheel you used in step 1. Optional: If top and bottom details were added to the hanger design in Step 2, cut them out with the Saw-Max and SM500 at this time.

STEP 5

Step 5

Mount the MM480 Wood Flush Cut Blade onto your MM30 tool. With your plank clamped, turn on your tool to a medium to high speed and cut vertically to connect each pair of bored slot holes. Tip: Let the speed of the tool do the work, not excess pressure. If you're noticing the blade is stuck mid-cut, back the tool out and plunge into your material again, working the tool side to side.

STEP 6

Step 6

Finally, we will sand the plank to give it a finished look. Attach the MM14 Hook and Loop Pad and MM70W Sand Paper to your MM30 tool. Turn on your tool to a medium speed, working in light circular motions and sand the body and edges of the plank as desired.

STEP 7

Step 7

Pull the rope through the cut hole. Tie a knot to secure the rope to the hanger. Finally, hang the piece and load your potted plants. Required rope length will vary based on your desired hanging height. We used 10' of rope for our hanger.

VIEW ALL STEPS SHOW LESS STEPS

Suggested Videos

VIEW ALL VIDEOS

Rotary Tool - Project

Creating Decorative Eggs

970

Rotary Tool - DIY

Cutting Vinyl Siding

963

Multi-Tool - DIY

Removing Vinyl Flooring

934

Rotary Tool - Project

Cutting Terra Cotta Lumniaries

861

VIEW ALL VIDEOS

Other Projects You Might Like

VIEW ALL PROJECTS
Patio Bench
furniture
Patio Bench

2years ago

Wall Mount Range Hood Vent
kitchen
Wall Mount Range Hood Vent

2years ago

Tabletop Greenhouse
lawn & garden
Tabletop Greenhouse

2years ago

Custom Stamp
craft and hobby
Custom Stamp

9months ago

VIEW ALL PROJECTS
No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

Submit A Project
No Promotion available!

A TOOL THAT CAN DO IT ALL

Experience Dremel's most powerful oscillating tool. Featuring 7.0 amps of power and 2 new, powerful cutting blades, the Dremel Velocity is the only tool you need.

Learn More

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.

SUPPORT