New

Organizational

Shelving

  like (0) I made it (0) Email Print
VIEW ALL Organizational

STEPS

5

SKILL LEVEL

Display your favorite holiday pictures & collectables with a unique decorative wall shelf. We constructed ours out of extra building materials we had on hand!

by Dremel ®

205 PROJECTS

Tags

organizational

Supplies Needed For This Project

TOOL

SM20-01 Saw-Max Tool Kit

Model # SM20

TOOL

4200 High-Performance Rotary Tool

Model # 4200

ACCESSORY

SM500 Wood & Plastic Carbide Wheel

Model # SM500

ACCESSORY

SM510 3" Metal Cut-Off Wheel

Model # SM510

ACCESSORY

628-01 Drill Bit Set

Model # 628-01

Tools & Accessories

Materials

  • 1

    24x24" piece of 3/4" thick mdf or plywood panel

  • 3

    3 foot section of different 3/4" thick trim moldings

  • 1

    6 foot length of 3/4" thick pine board, 3" width

  • 1

    3 foot length of 3/4" diameter pipe and 3 strap clamps

  • 1

    Drill & thin 1-1/2" wood screws

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

Start by cutting your 24" piece plywood or mdf into three 4" wide shelves. These quick rip cuts are easy with the Dremel Saw-Max equipped with the SM500 Wood & Plastic Wheel. Simply follow your marked lines of cut through the notch at the front end of the tool.

STEP 2

Step 2

Next, cut your choice of molding to trim the front and sizes of the three shelves. You can use your Saw-Max and SM500 wheel for these quick cuts as well. Be sure to clamp your trim in place and make your straight cut across your piece of trim. Glue and secure the trim to the front of each board with small brads.

STEP 3

Step 3

Next, using your Saw-Max tool, cut the 3" wide pine board to length. These boards will serve as your backing boards you'll secure your shelves to. For our shelving unit, we cut our pine into one piece about 36" long and one about 30" long. As with many weekends projects, these dimensions are adjustable according to the desired size of the project you are making.

STEP 4

Step 4

If you want to add another material type for decorative purposes as we did, pipe is an easy choice! We chose to add conduit to our shelving unit. Using your Saw-Max tool, swap out your blades and install a SM510 Metal Cutting Wheel to cut your secured metal pipe to about 34" in length. TIP: As your pipe may spark, wear gloves for this step.

STEP 5

Step 5

Next, select your final shelving layout. Lay out the two vertical boards cut in step 3. Take the 3 shelves already assembled and place them on the boards. Now, stagger and space the shelves to the desired look & height you want. Once in place, take a pencil and mark the backing boards where the shelf rests. Remove the shelves and drill pilot holes in the backing boards to accept the shelves. If you have a Dremel Rotary Tool handy, use your tool equipped with the 150 Drill Bit. Set your tool to high speed and make a quick, vertical plunge into the marks on your backing board. Secure the shelves to the backing board with screws. Repeat this process for all 3 shelves on one board. When one board is secure, line up the pencil marks and secure all three shelves onto the second backing board. Finally, place the decorative metal pipe between the backing boards and secure to each of the 3 shelves with a pipe strap. Secure hangers to the back of the vertical support.

VIEW ALL STEPS SHOW LESS STEPS

Suggested Videos

VIEW ALL VIDEOS

Rotary Tool - Project

Creating Decorative Eggs

970

Rotary Tool - DIY

Cutting Vinyl Siding

963

Rotary Tool - Project

Cutting Terra Cotta Lumniaries

861

3D Printer - Introduction

Dremel 3D Idea Builder Introduction

857

VIEW ALL VIDEOS

Other Projects You Might Like

VIEW ALL PROJECTS
Clean Golf Clubs
organizational
Clean Golf Clubs

11months ago

Mosaic Table
furniture
Mosaic Table

11months ago

Cat Tower
pets
Cat Tower

11months ago

Rain Barrel
home repair
Rain Barrel

9months ago

VIEW ALL PROJECTS
No Promotion available!

TOUR THE MAKER GALLERY

Explore the creations added to the Maker Gallery by Dremel Makers.

View Gallery
No Promotion available!

A TOOL THAT CAN DO IT ALL

Experience Dremel's most powerful oscillating tool. Featuring 7.0 amps of power and 2 new, powerful cutting blades, the Dremel Velocity is the only tool you need.

Learn More

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.

SUPPORT